Bluetooth Magnetic Credit Card / Driver's License
Reader and Transaction Receipt Printer

SETUP FOR SAMSUNG i730 POCKET PC

 

Just follow these easy steps setting up your Pocket Spectrum Printer to the Samsung i730 Pocket PC. Then configure Pocket Verifier to work with your Pocket Spectrum. Retire the wire!

 
Announcing a complete breakthrough in mobile printer design! A true Line Printer (the paper moves underneath a motionless head) , rated not in characters, but MILES of paper in reliability (31 to be precise)! Powered by powerful, built-in Nickel - Metal Hydride rechargeable batteries, this printer literally throws receipts out at up to 2 inches per second!

 

STEP 1: Reset your Pocket Spectrum.

Before you can pair the Pocket Spectrum with your iPAQ6315, the Pocket Spectrum should first be reset. To do this...

1. Turn off the Pocket Spectrum (if it is already on).
2. Press and Hold the ON button for at least 3 seconds.
3. When the paper starts advancing, release the ON button.
    A diagnostic sheet will be printed.
4. After the print out completes, the printer' bluetooth memory is cleared and ready for pairing to your PDA.
   

NOTICE:  If you are REINSTALLING a Pocket Spectrum, this will erase the existing pairing.  You MUST delete the connection in your PDA before performing the next step.


 

 

 From the "Today" Screen, tap on the Bluetooth Icon.

 

 

 Check both boxes

 

 Tap on "Devices" on the bottom of the screen,

Then tap on "New"

Make sure your Spectrum is ON

 

 The i730 will search for the Spectrum
 

 

 When found, the Spectrum will show up as 
"MPSxxxxxxxx"  The numbers will vary.

 

 Tap on the "MPS" Selection for the Spectrum,

 

Then tap "Next"

 

 Enter the Passcode 

1000

Then tap "Next"

 

 We cannot sync to the printer, so tap "NO"

 

 Now, tap "Finish"

 

 The display will show the installed device.

 

 Now, we need to assign a port for it to talk to, tap on the "Com Ports" tab on the bottom.

 

Then tap on  "New Outgoing Port"

 

 Select the printer, then tap "Next"

 

 Accept the default port (Com 2), check "Secure Connection", and tap "OK"

 

 Tap OK again to complete the Bluetooth setup.

 

NOTE: AT THIS POINT TURN THE CARD READER OFF, WAIT A MINUTE, THEN TURN IT BACK ON.
     Setup Pocket Verifier for Outgoing Com Port.

       1.   Open Pocket Verifier.
       2.   Log into your account.
       3.   Go to the Options screen.

       4.   Change Printer/Reader to Pocket Spectrum.

       5.   Tap Settings, then Port Settings.
       6.   Change Port Settings to 38400,N,8,1
       7.   Tap Ok.

       8.   Tap Settings, then Com Port.
       9.   Change Port Number to the Outbound COM Port determined  above (i.e., 2.).
       10. Tap Ok.
       11. Tap Accept.
 

       
                           4                                                       5,6,7                                                  8,9
   
   

The Samsung i730 is now setup to work with the Pocket Verifier software and Pocket Spectrum!

If you are on the sales screen when the Pocket Spectrum is off and you would like to read a card, turn on the printer, wait for the single beep and linefeed, then click on the blue Bluetooth icon at the top right of the screen. The icon will turn red briefly until communications are established.

 



Copyright © 2001 Advanced Merchant Solutions, Inc. All Rights Reserved.
All artwork, logos, Pocket Verifier, PC Verifier, and MerchantAnywhere.com are trademarks of Advanced Merchant Solutions, Inc.